Her er full OpenWrt bootlog fra et av mine forsøk:
Kode
ROM VER: 1.1.0
CFG 06
NAND
DDR autotuning Rev 0.3d
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...
U-Boot 2010.06-LANTIQ-v-2.2.28-JPR-v1.04-dirty (Feb 21 2014 - 18:08:35)
CLOCK CPU 600M RAM 300M
16 Bit RAM
DRAM: 128 MiB
NAND: ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In: serial
Out: serial
Err: serial
Net: internal phy using 25Mhz clock
Internal phy firmware version: 0x8434
ar10 Switch
Type "run flash_nfs" to mount root filesystem over NFS
part1_err=0,part2_err=0
Hit any key to stop autoboot: 0
OG461X # setenv loadaddr 0x84000000
OG461X # run net_ram
Using ar10 Switch device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'uImage'.
Load address: 0x84000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
############################
done
Bytes transferred = 4218401 (405e21 hex)
## Booting kernel from Legacy Image at 84000000 ...
Image Name: MIPS OpenWrt Linux-4.14.96
Created: 2019-02-01 9:58:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4218337 Bytes = 4 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.14.96 (bjorn@canardo) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9079-1fdb4a7907e0)) #0 SMP Mon Jan 28 20:39:35 2019
[ 0.000000] SoC: xRX300 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is D-Link DWR-956
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Detected 1 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x4a0 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu @8110b000 s25936 r8192 d23216 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=000288e0
[ 0.000000] Readback ErrCtl register=000288e0
[ 0.000000] Memory: 115948K/131072K available (4942K kernel code, 189K rwdata, 1468K rodata, 6952K init, 228K bss, 15124K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 600MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[ 0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[ 0.007890] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[ 0.045928] pid_max: default: 32768 minimum: 301
[ 0.050805] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.057334] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.066449] Hierarchical SRCU implementation.
[ 0.071720] smp: Bringing up secondary CPUs ...
[ 0.077003] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.077014] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.077147] CPU1 revision is: 00019556 (MIPS 34Kc)
[ 0.104313] Synchronize counters for CPU 1: done.
[ 0.128583] smp: Brought up 1 node, 2 CPUs
[ 0.135927] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.145586] futex hash table entries: 512 (order: 2, 16384 bytes)
[ 0.151844] pinctrl core: initialized pinctrl subsystem
[ 0.158160] NET: Registered protocol family 16
[ 0.172471] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.178638] dma-xway 1e104100.dma: Init done - hw rev: 8, ports: 5, channels: 24
[ 0.187400] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 0 mV
[ 0.218047] gpio-stp-xway 1e100bb0.stp: Init done
[ 0.223412] usbcore: registered new interface driver usbfs
[ 0.229020] usbcore: registered new interface driver hub
[ 0.234401] usbcore: registered new device driver usb
[ 0.241551] clocksource: Switched to clocksource MIPS
[ 0.247865] NET: Registered protocol family 2
[ 0.252978] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.259902] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.266275] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.272864] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.278623] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.285360] NET: Registered protocol family 1
[ 0.481394] gptu: totally 6 16-bit timers/counters
[ 0.486241] gptu: misc_register on minor 63
[ 0.490385] gptu: succeeded to request irq 126
[ 0.494883] gptu: succeeded to request irq 127
[ 0.499382] gptu: succeeded to request irq 128
[ 0.503848] random: fast init done
[ 0.507380] gptu: succeeded to request irq 129
[ 0.511897] gptu: succeeded to request irq 130
[ 0.516396] gptu: succeeded to request irq 131
[ 0.521058] No VPEs reserved for AP/SP, not initialize VPE loader
[ 0.521058] Pass maxvpes=<n> argument as kernel argument
[ 0.532459] No TCs reserved for AP/SP, not initializing RTLX.
[ 0.532459] Pass maxtcs=<n> argument as kernel argument
[ 0.545066] Crashlog allocated RAM at address 0x3f00000
[ 0.550653] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.568106] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.573856] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.590049] io scheduler noop registered
[ 0.593875] io scheduler deadline registered (default)
[ 0.602511] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.611490] console [ttyLTQ0] enabled
[ 0.611490] console [ttyLTQ0] enabled
[ 0.618704] bootconsole [early0] disabled
[ 0.618704] bootconsole [early0] disabled
[ 0.627658] cacheinfo: Failed to find cpu0 device node
[ 0.631443] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.638786] nand: nand_detect: got 0x01/0xf1
[ 0.641623] nand: (null): running nand_flash_detect_onfi
[ 0.647055] nand: nand_detect: done
[ 0.650356] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.656677] nand: AMD/Spansion S34ML01G1
[ 0.660550] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.668085] Scanning device for bad blocks
[ 0.739749] 6 fixed-partitions partitions found on MTD device 14000000.nand
[ 0.745268] Creating 6 MTD partitions on "14000000.nand":
[ 0.750614] 0x000000000000-0x000000040000 : "uboot"
[ 0.757011] 0x000000040000-0x000000080000 : "ubootconfig"
[ 0.762543] 0x000000080000-0x0000000c0000 : "gphyfirmware"
[ 0.768080] 0x0000000c0000-0x000000100000 : "dataA"
[ 0.773019] 0x000000100000-0x000007900000 : "ubi"
[ 0.779221] 0x000007900000-0x000007a00000 : "res"
[ 0.787242] libphy: Fixed MDIO Bus: probed
[ 0.793598] wdt 1f8803f0.watchdog: Init done
[ 0.799215] NET: Registered protocol family 10
[ 0.804357] Segment Routing with IPv6
[ 0.806737] NET: Registered protocol family 17
[ 0.811077] 8021q: 802.1Q VLAN Support v1.8
[ 1.401303] lantiq-reset 1f203010.reset-controller: Failed to assert bit 27
[ 1.508765] libphy: lantiq,xrx200-mdio: probed
[ 1.610150] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:00, irq=POLL)
[ 1.626505] UBI: auto-attach mtd4
[ 1.628374] ubi0: attaching mtd4
[ 1.762680] ubi0: scanning is finished
[ 1.779211] ubi0: attached mtd4 (name "ubi", size 120 MiB)
[ 1.783253] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 1.790075] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 1.796738] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 1.803478] ubi0: good PEBs: 960, bad PEBs: 0, corrupted PEBs: 0
[ 1.809440] ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[ 1.816591] ubi0: max/mean erase counter: 80/1, WL threshold: 4096, image sequence number: 0
[ 1.824981] ubi0: available PEBs: 23, total reserved PEBs: 937, PEBs reserved for bad PEB handling: 20
[ 1.834302] ubi0: background thread "ubi_bgt0d" started, PID 390
[ 1.840236] block ubiblock0_1: created from ubi0:1(rootfs)
[ 1.840252] ubiblock: device ubiblock0_1 (rootfs) set to be roo[ 1.872787] Freeing unused kernel memory: 6952K
[ 1.875903] This architecture does not have kernel memory protection.
[ 1.899764] init: Console is alive
[ 1.902063] init: - watchdog -
[ 1.925745] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 1.939450] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 1.946330] init: - preinit -
[ 2.065526] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.211080] procd: - early -
[ 5.212654] procd: - watchdog -
[ 5.803673] procd: - watchdog -
[ 5.805930] procd: - ubus -
[ 5.815628] random: ubusd: uninitialized urandom read (4 bytes read)
[ 5.858693] random: ubusd: uninitialized urandom read (4 bytes read)
[ 5.864178] random: ubusd: uninitialized urandom read (4 bytes read)
[ 5.871578] procd: - init -
Please press Enter to activate this console.
[ 5.944220] random: crng init done
[ 5.946162] random: 5 urandom warning(s) missed due to ratelimiting
[ 6.078077] kmodloader: loading kernel modules from /etc/modules.d/*
[ 6.085925] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 6.094924] NET: Registered protocol family 8
[ 6.097876] NET: Registered protocol family 20
[ 6.107540] PPP generic driver version 2.4.2
[ 6.115981] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 6.205596] kmodloader: failed to load drv_mei_cpe
[ 6.216354] drv_dsl_cpe_api: Unknown symbol MEI_InternalXtmSwhowtimeEntrySignal (err 0)
[ 6.222972] drv_dsl_cpe_api: Unknown symbol MEI_InternalDevClose (err 0)
[ 6.229590] drv_dsl_cpe_api: Unknown symbol MEI_InternalNfcMsgRead (err 0)
[ 6.236460] drv_dsl_cpe_api: Unknown symbol MEI_InternalMsgSend (err 0)
[ 6.242972] drv_dsl_cpe_api: Unknown symbol MEI_InternalCallbackSet (err 0)
[ 6.249939] drv_dsl_cpe_api: Unknown symbol MEI_InternalDrvVersionGet (err 0)
[ 6.257028] drv_dsl_cpe_api: Unknown symbol MEI_InternalRequestConfig (err 0)
[ 6.264112] drv_dsl_cpe_api: Unknown symbol MEI_InternalDevReset (err 0)
[ 6.270711] drv_dsl_cpe_api: Unknown symbol MEI_InternalNfcEnable (err 0)
[ 6.277452] drv_dsl_cpe_api: Unknown symbol MEI_InternalInitDevice (err 0)
[ 6.284302] drv_dsl_cpe_api: Unknown symbol MEI_InternalXtmSwhowtimeExitSignal (err 0)
[ 6.292140] drv_dsl_cpe_api: Unknown symbol MEI_InternalFirmwareDownload (err 0)
[ 6.299498] drv_dsl_cpe_api: Unknown symbol MEI_InternalFwModeCtrlSet (err 0)
[ 6.306575] drv_dsl_cpe_api: Unknown symbol MEI_InternalDevOpen (err 0)
[ 6.338445] drv_dsl_cpe_api: Unknown symbol MEI_InternalXtmSwhowtimeEntrySignal (err 0)
[ 6.345131] drv_dsl_cpe_api: Unknown symbol MEI_InternalDevClose (err 0)
[ 6.351682] drv_dsl_cpe_api: Unknown symbol MEI_InternalNfcMsgRead (err 0)
[ 6.358528] drv_dsl_cpe_api: Unknown symbol MEI_InternalMsgSend (err 0)
[ 6.365123] drv_dsl_cpe_api: Unknown symbol MEI_InternalCallbackSet (err 0)
[ 6.372030] drv_dsl_cpe_api: Unknown symbol MEI_InternalDrvVersionGet (err 0)
[ 6.379096] drv_dsl_cpe_api: Unknown symbol MEI_InternalRequestConfig (err 0)
[ 6.386218] drv_dsl_cpe_api: Unknown symbol MEI_InternalDevReset (err 0)
[ 6.392816] drv_dsl_cpe_api: Unknown symbol MEI_InternalNfcEnable (err 0)
[ 6.399532] drv_dsl_cpe_api: Unknown symbol MEI_InternalInitDevice (err 0)
[ 6.406381] drv_dsl_cpe_api: Unknown symbol MEI_InternalXtmSwhowtimeExitSignal (err 0)
[ 6.414237] drv_dsl_cpe_api: Unknown symbol MEI_InternalFirmwareDownload (err 0)
[ 6.421591] drv_dsl_cpe_api: Unknown symbol MEI_InternalFwModeCtrlSet (err 0)
[ 6.428680] drv_dsl_cpe_api: Unknown symbol MEI_InternalDevOpen (err 0)
[ 6.449634] kmodloader: failed to load drv_dsl_cpe_api
[ 6.454994] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 6.469893] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 6.516375] NET: Registered protocol family 24
[ 6.533905] xt_time: kernel timezone is -0000
[ 6.544402] kmodloader: 2 modules could not be probed
[ 6.548218] kmodloader: - drv_dsl_cpe_api - 0
[ 6.552523] kmodloader: - drv_mei_cpe - 0
BusyBox v1.30.0 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r9223+6-a5269ffa7a46
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#